This equipment use without frame design, 8-channel ultrasonic flaw detector to perform full coverage inspection of the weld seam, and the weld is forcibly cooled by water before the test.
Spiral steel pipe online weld ultrasonic flaw detection equipment is mainly composed of weld servo machine, weld probe frame, spray marking mechanism, water supply unit, electrical control system, testing instrument and probe system, computer data processing and recording unit and video monitoring unit.
General specification:
Pipe Specification
Pipe O.D. : According to the centralizer
Pipe wall thickness: 5-16mm
Pipe pitch: 2000mm
Weld seam width: 8-20mm
Weld seam height: 1-3.2mm
Material: Low-carbon steel except austenite
Pipe bending degree: ≤0.2% / meter
Test process Specification
Test items: Cracks, unfused, stomata, and slag inclusions of welds are tested.
Longitudinal and lateral inspection of welds, heat-affected zone defect detection
Test area: 100% Welding seam test
Heat affected zone: Within welding seam both side 25mm
Test sensitivity: Radial hole: φ1.6mm&3.2mm
N5 Rectangular groove: depth: 5% of wall thickness, Minimum 0.3 mm
Length: 30 mm, Max. width: 1.0 mm
Heat affected zone defect: Flat bottom hole: Ф 6 mm, Depth: 50% of wall thickness
Equipment list:
1-8 channel ultrasonic testing machine
1-Ultrasonic Operating machine
1-Related software
8-Welding seam testing probe
8-Probe wire
1-Operator console and electrical control cabinet
1-Monitor display
1-Cable and towline
8-Welding seam testing probe Holder
8-Welding seam testing probe set combination
1-Weld seam servo head section
1-Servo traverse device
1-Servo 360° rotary table
1-Spray Marking device
1-Water and gas unit
1-Manual tracking device
The machine in the warehouse, ready to pick.
if you have interest this machine or a similar one.
Pls contact info@huaye.us.
Spiral steel pipe online weld ultrasonic flaw detection equipment is mainly composed of weld servo machine, weld probe frame, spray marking mechanism, water supply unit, electrical control system, testing instrument and probe system, computer data processing and recording unit and video monitoring unit.
General specification:
Pipe Specification
Pipe O.D. : According to the centralizer
Pipe wall thickness: 5-16mm
Pipe pitch: 2000mm
Weld seam width: 8-20mm
Weld seam height: 1-3.2mm
Material: Low-carbon steel except austenite
Pipe bending degree: ≤0.2% / meter
Test process Specification
Test items: Cracks, unfused, stomata, and slag inclusions of welds are tested.
Longitudinal and lateral inspection of welds, heat-affected zone defect detection
Test area: 100% Welding seam test
Heat affected zone: Within welding seam both side 25mm
Test sensitivity: Radial hole: φ1.6mm&3.2mm
N5 Rectangular groove: depth: 5% of wall thickness, Minimum 0.3 mm
Length: 30 mm, Max. width: 1.0 mm
Heat affected zone defect: Flat bottom hole: Ф 6 mm, Depth: 50% of wall thickness
Equipment list:
1-8 channel ultrasonic testing machine
1-Ultrasonic Operating machine
1-Related software
8-Welding seam testing probe
8-Probe wire
1-Operator console and electrical control cabinet
1-Monitor display
1-Cable and towline
8-Welding seam testing probe Holder
8-Welding seam testing probe set combination
1-Weld seam servo head section
1-Servo traverse device
1-Servo 360° rotary table
1-Spray Marking device
1-Water and gas unit
1-Manual tracking device
The machine in the warehouse, ready to pick.
if you have interest this machine or a similar one.
Pls contact info@huaye.us.
RSS Feed